Heat pumps across LD2 (Builth Wells) postcode area: 2026 grant + cost guide

What the EPC data shows for LD2 (Builth Wells)

We’ve aggregated the current Energy Performance Certificate band for 1,495 properties in LD2 (Builth Wells), drawn live from the GOV.UK EPC Register. The median home in our sample sits at band D, with 35% falling into band D and 24% in band C. Around 71% of homes are at band D or below — the cohort with the most realistic retrofit upside.

The typical LD2 (Builth Wells) home

What the EPC data shows beyond the headline rating — useful context for sizing a heat-pump install.

• Floor area: median 99 m² (25th–75th percentile: 72–143 m²). Heat-pump sizing scales roughly with floor area — expect a 5–8 kW unit at the median.
• Current heating cost: median £953/yr (£600– £1,507 typical range). The number an installer’s running-cost saving projection sits against.
• Mains gas connection: 46% of properties. Predominantly off-grid — heat-pump running-cost case is unambiguous vs oil and LPG.
• Property type mix: Detached 48%, End-Terrace 10%, Mid-Terrace 14%, Semi-Detached 26%.
• Dominant age band: England and Wales: before 1900 (29% of homes). Sets the fabric-first work expected before commissioning.

Does the Boiler Upgrade Scheme apply in LD2 (Builth Wells)?

Yes. LD2 (Builth Wells) is in Wales, where the Boiler Upgrade Scheme (BUS) pays £7,500 toward an air-source heat pump install. The grant is administered by Ofgem and deducted by the installer at the point of invoice — you never see the cash. To qualify, the property must be owner-occupied or privately rented, have a valid EPC issued in the last 10 years, and have no outstanding loft-or-cavity insulation recommendation on the EPC (unless an exemption is documented). In our sample of LD2 (Builth Wells) EPCs the median rating is band D, which means most homes need to clear at least one insulation recommendation before the installer can claim the grant.

Typical install cost in LD2 (Builth Wells)

Pre-grant install costs in LD2 (Builth Wells) typically run £8,000 to £14,000 for a 5–10 kW air-source unit, in line with UK averages — labour rates in W99999999 sit close to the national mean. After the £7,500 BUS deduction most LD2 (Builth Wells)homeowners pay £1,500 to £6,500 out of pocket. The figure within that range that applies to your property depends on three things: heat-loss sizing (set by floor area, fabric and air-tightness), radiator upgrades (most pre-2000s homes need at least one or two changed), and hot-water cylinder provision. An MCS-certified engineer issues the binding quote after a heat-loss calculation per BS EN 12831.

What this means for your home

Whether a heat pump is a good fit for your specific home in LD2 (Builth Wells)depends on three factors the EPC alone can’t answer: roof + outdoor space for the external unit, radiator sizing throughout the heating circuit, and your current heating fuel + tariff. Propertoasty’s free pre-survey check combines your address, an EPC pull, the Google Solar API’s roof data, and a floorplan vision analysis to produce an installer-ready report — typically takes about five minutes.

Run a free pre-survey check on your home — installer-ready report, BUS-eligibility verdict, sizing range, and a list of MCS-certified installers covering LD2 (Builth Wells).

How LD2 (Builth Wells) compares

Compared with the England + Wales average band-D share of roughly 45%, LD2 (Builth Wells)’s 35% sits below the national midpoint. Bands E and worse — typical pre-1930s homes without significant retrofit — make up 37% of the local sample, which compares to the E&W average of around 22%.